HOME
    PRODUCTS
       » Ambulances
       » GEM Cars
       » Chief & EMS Conversions
       » Re-Conditions Police Vehicles
       » Used Inventory
    VIDEOS
       » Day in the Life
       » Public Service
       » Comparsion
    SERVICES
    ABOUT US
    CONTACT US
    LINKS
  RVS PRODUCTS - MEDTEC Field Duty 160
 
Field Duty 160 | Type III

The FD-160 is a full-sized, high featured Type III with plenty of storage and patient care configurations. It is everything you need from an affordable, value-priced ambulance.
Chassis
  • Ford E-450, 158" Wheelbase, 14,050 GVWR, 6.0L Powerstroke Diesel Engine, #47A Ambulance Prep Package, AM/FM/CD

Electrical

  • Circuit Board: Printed circuit board with automatic reset circuit breakers; a complete set of relays and circuit breakers are mounted in the electrical cabinet as spares 
  • Heat/Cool: A combination heating and cooling unit installed over the walk-through with 3-position mode selector switch and thermostat on the rear control panel; two automatic gate valves to shut off hot water from engine when in air conditioning mode; all heater hoses are EDPM Nomex material
  • 3 - 115-volt hospital grade duplex outlets with GFI protection
  • Shoreline: 115-Volt 20amp twist-lock power inlet with watertight cover; with mating plug
  • 2 - 12-Volt power point-style outlets; Schottky diode to isolate medical equipment
Body
  • Headroom: 68" floor to ceiling, with optional increased headroom available
  • Flooring: Non-slip Lonplate II
  • Compartments: .090" bright aluminum diamond plate wall construction; .125" smooth aluminum floors
  • Body Construction: Structural members are 1"x2"x.125" aluminum tubes at 12" on center for sidewall verticals, roof cross members, and floor cross members; sidewall skin is .125" aluminum sheet; roof skin is a .090" 1-piece aluminum sheet; floor vapor barrier is a .090" 1-piece aluminum sheet; doorjambs are formed integral in the sidewall .125" skin.
  • Side Entry Stepwell: .125" ADP single step side entry stepwell
  • Door Construction: One-piece, form rolled, compartment and entry doors with 24 bends to form a minimum 2.75" thick door. Tri-Mark heavy duty locking paddle handles with 2-point double latching on all compartment and entry doors
  • Rear Bumper/ Step: 8" open grate flip-up center section with ADP endpods
  • Rubrails: All aluminum C-channel style
  • Rear Kickplate/Stone Guards: Brushed stainless steel

Emergency Lights

  • Headroom: 68" floor to ceiling, with optional increased headroom available
  • Flooring: Non-slip Lonplate II
  • Compartments: .090" bright aluminum diamond plate wall construction; .125" smooth aluminum floors
  • Body Construction: Structural members are 1"x2"x.125" aluminum tubes at 12" on center for sidewall verticals, roof cross members, and floor cross members; sidewall skin is .125" aluminum sheet; roof skin is a .090" 1-piece aluminum sheet; floor vapor barrier is a .090" 1-piece aluminum sheet; doorjambs are formed integral in the sidewall .125" skin.
  • Side Entry Stepwell: .125" ADP single step side entry stepwell
  • Door Construction: One-piece, form rolled, compartment and entry doors with 24 bends to form a minimum 2.75" thick door. Tri-Mark heavy duty locking paddle handles with 2-point double latching on all compartment and entry doors
  • Rear Bumper/ Step: 8" open grate flip-up center section with ADP endpods
  • Rubrails: All aluminum C-channel style
  • Rear Kickplate/Stone Guards: Brushed stainless steel

Cabinets and Hardware

  • IV Holders: 2 recessed, in ceiling
  • Technician's Seat: High-back captain's chair with left-side armrest and swivel base; Seamless vacuum formed upholstery
  • Cabinets: Pull-out writing tray below primary action area; sharps container ships loose; biohazard container with lid and red biohazard bags shipped loose; all adjustable shelves have infinitely adjustable C-channel mounting tracks; all cabinet interior corners are sealed for ease in clean up; all cabinet faces have picture framed windows with mitered corners.
  • Squad Bench: Split lids with storage below; double cushions fastened with Velcro; gas-prop style hold opens (lid automatically opens when latch is released); stainless steel paddle latches to hold the lids securely closed; seatbelts for seated and supine positions

Oxygen/Vacuum

  • Oxygen and Vacuum Outlets: 2 Ohio-style oxygen outlets and one vacuum outlet
  • Oxygen Cylinder Mount: Adjustable stainless steel rings for M-size cylinder, located in the streetside front compartment
  • Vacuum and Suction System: Thomas brand vacuum pump in streetside intermediate compartment; 1 on/off vacuum switch at rear console; aspirator with disposable canister mounted on action wall



View Video: High | Medium
Field Duty FD-160 Brochure
Field Duty Van Drawing
 
Registered Dealer for Southern California
For more information, contact

Geoff Maze
geoff@responsevehiclesolutions.com
Office: 818-780-6272
Cell: 818-738-4584